LCD Screen ILI9341 TFT

If you are not familiar with SPI, please read Introduction to SPI first.

Materials

• AMB82-mini x 1

• ILI9341 TFT LCD with SPI interface x 1

Example

We have tested the following two models of ILI9341 TFT LCD with SPI interface:

• Adafruit 2.8″ TFT LCD (with touch screen)

  • https://www.adafruit.com/products/1651

  • https://learn.adafruit.com/adafruit-2-8-tft-touch-shield-v2?view=all

• QVGA 2.2″ TFT LCD

  • http://www.lcdwiki.com/2.2inch_SPI_Module_ILI9341_SKU:MSP2202

Common pins in ILI9341 TFT LCD with SPI interface:

• MOSI: Standard SPI Pin

• MISO: Standard SPI Pin

• SLK: Standard SPI Pin

• CS: Standard SPI Pin

• RESET: Used to reboot LCD.

• D/C: Data/Command. When it is at LOW, the signal transmitted are commands, otherwise the data transmitted are data.

• LED (or BL): Adapt the screen backlight. Can be controlled by PWM or connected to VCC for 100% backlight.

• VCC: Connected to 3V or 5V, depends on its spec.

• GND: Connected to GND.

AMB82 MINI and QVGA TFT LCD Wiring Diagram:

AMB82 MINI and Adafruit 2.8” TFT LCD touch shield:

Please note that this shield model enables the backlight by default and pin 8 is not for backlight, and the VCC should be connected to 5V.

Open the example, “File” -> “Examples” -> “AmebaSPI” -> “LCD_Screen_ILI9341_TFT”

Compile and upload to Ameba, then press the reset button.

Then you can see some display tests appear on the LCD screen, such as displaying different colors, drawing vertical and horizontal lines, drawing circles, etc.…

Besides, it can also display any user images based on the screen size. Using the online Image converting tool here that supports input images in png, .jpg and .gif ad output as .c file. Upon converting is done, place the .c file in our template Amebalogo.h file and upload the code again.

Code Reference

•  RGB 16-bit

  ILI9341 uses RGB 16-bit to display colors. Different from RGB 24-bit, it uses 5 bits for red, 6 bits for green, 5 bits for blue. For example, the RGB 24-bit representation of sky blue is 0x87CEFF, that is in binary:

  • Red: 0x87 = B10000111

  • Green: 0xCE = B11001110

  • Blue: 0xFF = B11111111

and converted to RGB 16-bit:

• Red: B10000

• Green: B110011

• Blue: B11111

Then concatenate them, which forms B1000011001111111 = 0x867F

• Drawing of ILI9341

  • First you must specify the range of the rectangle to draw, then pass the 2-byte RGB 16-bit color to ILI9341 corresponding to each pixel one by one, in this way ILI9341 fills each color to each pixel.

  • You still must specify the drawing range even though the range covers only one pixel.

  • From the rules we mentioned above, we can conclude that drawing vertical or horizontal lines are faster than diagonal lines.

• Printing text on ILI9341

  • In our API, each character is 5x7 but each character is printed to size 6x8 (its right side and below are left blank), so as to separate from next character. For example, the character “A”:

    

  • The font size represents the dot size. For example, if the font size is 2, each dot in the character is a 2x2 rectangle

• Screen rotation

  • ILI9341 provides 0, 90, 180, 270 degrees screen rotation.

  • If the original width is 240 and original height is 320, when the screen rotates 90 degrees, the width becomes 320 and the height becomes 240.